- #HOW TO FACTORY RESET HP JETDIRECT 170X HOW TO#
- #HOW TO FACTORY RESET HP JETDIRECT 170X WINDOWS 7#
- #HOW TO FACTORY RESET HP JETDIRECT 170X MAC#
- #HOW TO FACTORY RESET HP JETDIRECT 170X WINDOWS#
Apparently it is also unsigned and thus cannot run. When you press the "Scan" button, another java program is called to handle the scan. The initial java program that runs handles the "Home" and "Administration" buttons. It is one of the three buttons on the left. The web interface to the HP Jetdirect 170x boxes includes a "Scan" button.
#HOW TO FACTORY RESET HP JETDIRECT 170X WINDOWS#
And again I tried the usual three browsers.ĭoes anyone know if this is a browser thing, a Windows thing or something else configured on the network or the server? It was fully up to date but I get the same error again even though I'm logged in as an admin.
#HOW TO FACTORY RESET HP JETDIRECT 170X WINDOWS 7#
I thought it was something to do with Windows 7 or the fact I'm not on the domain (don't remember this being an issue before) so I tried it on a Windows XP machine that I had just formatted and re set up. I tried using Firefox 26, Chrome and IE 11.
This is what I get when trying it from my laptop which is Windows 7 and not on the domain in the school. Using JRE version 1.7.0_51-b13 Java HotSpot(TM) Client VM When I click the details button I get a Java Console load up with the following text: When I click that I get the same error message and a details button. I have to click ok four times and the page loads with "Error - Click here for details" in each of the panels. Your Security Settings have blocked an untrusted application from running I see the Java logo and the spinning circle and then I get four error messages (all the same) for each panel. The four panels you normally see when connecting to the web interface begin to load. I was just trying to log in to one to reconfigure its IP address when I moved the printer's location and I can't get in. Or type "exit" to exit without saving configuration parameter entries Let's change the IP address, subnet mask, and default gateway: > ip: 10.50.100.We have a couple of HP Jetdirect 170x boxes around the school connected to a HP 4200 and a HP Plotter. Type "?" for HELP, "/" for current settings or "quit" to save-and-exit.
#HOW TO FACTORY RESET HP JETDIRECT 170X MAC#
: F.08.20 MAC Address : 00:01:e6:28:03:e0 Config By : USER SPECIFIED IP Address : 10.50.100.8 Subnet Mask : 255.255.255.0 Default Gateway : 10.50.100.82 Syslog Server : Not Specified Idle Timeout : 90 Seconds Set Cmnty Name : Not Specified Host Name : Not Specified DHCP Config : Disabled Passwd : Disabled IPX/SPX : Disabled DLC/LLC : Disabled Banner page : Enabled > ? To Change/Configure Parameters Enter: Parameter-name: value Parameter-name Type of value ip: IP-address in dotted notation subnet-mask: address in dotted notation (enter 0 for default) default-gw: address in dotted notation (enter 0 for default) syslog-svr: address in dotted notation (enter 0 for default) idle-timeout: seconds in integers set-cmnty-name: alpha-numeric string (32 chars max) host-name: alpha-numeric string (upper case only, 32 chars max) dhcp-config: 0 to disable, 1 to enable allow: (0 to clear, list to display, 10 max) addrawport: ( 3000-9000) deleterawport: listrawport: (No parameter required) ipx/spx: 0 to disable, 1 to enable dlc/llc: 0 to disable, 1 to enable banner: 0 to disable, 1 to enable Type passwd to change the password.
HP JetDirect Please type "?" for HELP, or "/" for current settings > / =JetDirect Telnet Configuration= Firmware Rev.
#HOW TO FACTORY RESET HP JETDIRECT 170X HOW TO#
How to check the current IP: attach a PCL compatible printer, press the test button on the 170X and this should tell you what IP address the 170X currently has.Ĭhange IP (You may can not see what you typed in telnet windows but don't worry just go ahead.
The default address after reset is 192.0.0.192 so you need a crossover cable if you are plugging the JetDirect into a PC, and a normal cable if using hub or switch. Unplug the power cord, then hold down the TEST button for 5 to 30 seconds while plugging in the power cord. You can get it back to the default address by doing a cold reset. If JetDirect 170x has been used on a real network then the address will almost certainly have been changed.
0 kommentar(er)
